Power and light for the garage you actually use
Power for a real workshop: 240-volt outlets, a heater circuit, bright lights and outlets where the bench is. Planned with you, so the garage is wired once.
Garage Wiring and Power Installation Services
Garage wiring in Duluth, from Heyday Home Solutions, means circuits sized for what you'll run out there: 240-volt outlets for a welder, compressor or heater, GFCI outlets along the walls and bright lighting. For a detached garage it often starts with a subpanel. Cory Hesselgrave, our electrician, does the work. Call (715) 817-2419 or ask for a free quote.
What is involved
A heater, a welder, a compressor, a freezer, an EV charger, power tools. The list sets the size of everything else.
It has to carry the garage on top of the house.
An attached garage may run off new circuits from the house panel. A detached one usually gets a feeder and its own subpanel, buried or run overhead.
Outlets at bench height where you work, 240-volt outlets where the big tools sit, and lights over the bench and the doors.
with GFCI protection on the garage outlets.

Recent project
On the outskirts of Superior, we built a new garage and workshop big enough to store recreational vehicles and still work in. See the garage and workshop build.
Cost
Distance and load set most of the price. A few outlets and lights in an attached garage, near the panel, is a short job. A detached garage 60 feet away with a subpanel, a heater circuit and a 240-volt welder outlet means a trench or an overhead line, plus more wire and breakers. Finished walls take longer to wire than open studs.
Signs it is time
It also does if the garage shares one 15-amp circuit with the house. Watch for a breaker that trips when the space heater and a saw run together, or for extension cords strung from one outlet. A Duluth winter makes this worse, because the heater is on for months. A garage with its own circuits, or a subpanel, stops the trips and keeps the house circuits free.
Hire an electrician for your garage when you need 240 volts, a subpanel or a new feed from the house. Those are the jobs that usually need a permit and an inspection, and the ones that go wrong when guessed at. A 240-volt outlet has to match the tool's plug and amps; a welder and a heater rarely use the same one. Plan the lights for the work, not just the parking: over the bench, the doors and wherever you'll be on your back under a car. Bring your list of tools to the estimate and we'll size the garage to it, with room for what you might add later.

The Heyday experience
Two things we help with before the work starts: paying for it over time, and getting an insurance claim through to a finished repair.
Financing runs through Acorn. You answer a few questions, compare loan offers from several lenders in one place, and apply with the one you choose. The loan is between you and that lender: we don’t issue it, and Acorn doesn’t pay us.
After storm or water damage, call your insurer first so they can assign an adjuster. Once the area is dried out and safe, we assess everything that needs rebuilding, including damage that only shows after cleanup, and write the estimate in the format adjusters work from. Their questions, any supplements and the approvals go through us. Then we schedule the rebuild.
What clients say
We had a very good experience with Heyday. They completely gutted and remodeled our master bathroom. I loved working with Amanda on the planning.
The crew at Heyday did a fantastic job on our new roof! The cleanup afterwards was impeccable, and the communication from management was top-notch!
Josh and his crew are terrific. The quality of their work is first rate - whether it be new construction or repair work or trouble shooting.
Usually, if you want more than a light and an outlet or two. A subpanel lets the garage have several circuits, including 240-volt ones, fed by one line from the house. It also gives you breakers in the garage, so you can reset one without walking to the basement. We size it to your tool list.
Yes. The outlet, wire and breaker are matched to the tool's nameplate, so bring the model or a photo of the label to the estimate. A welder and a garage heater often need different outlets and amps. If the panel is already full, we'll tell you what it takes to make room.
Yes. Current code calls for GFCI protection on garage outlets, because garages are damp and have concrete floors. That includes the outlet you'd plug a freezer into. Older garages often have none, so we add it when we rewire, either at the outlet or at the breaker.
We plan the job with you first: what you'll run, where the bench goes and what your panel can carry. We explain the options so you can choose with confidence. Cory Hesselgrave, our electrician, does the wiring, and we show up when we say we will and work cleanly.
Your project
We will look at the space with you, listen to what you want, and explain your options before anything is decided.